Page tree

Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Published by Scroll Versions from space NWUG and version 2.24.0

...

  1. Download the Workbench installation package from https://support.neonode.com/docs/pages/viewpage.action?pageId=2490816. here.
  2. Unzip the installation package. 
  3. Open the unzipped installation package folder.
  4. Run the Workbench installer (.msi file) and follow the instructions.
  5. Open the installation package folder again. 
  6. Unzip the Workspace folder to a location where you have write permissions. Write permissions are required to save settings and user data.

    Info

    In order for the Workbench application to operate, the files in the Workspace folder must be kept together. Move the entire folder if you want to relocate the workspace file.

...

Status or error information appear on occasion in the top center of the Workbench application. For example, a status notification appears when a sensor Touch Sensor Module (previously referred to as zForce AIR) is connected or disconnected.

Accessing

...

Sensor Module Information

In the left panel, double-click the item zForce AIR Sensor Gadget.  Sensor The sensor module information such as firmware version, protocol version, etc shows in the right panel.In the left panel, double-click the item zForce AIR Sensor Device. Two sections, Control Panel and Device Configuration, show in the right panel.

  1. In the right panel, click the Is Enabled checkbox to enable or disable the sensor. 
  2. Select communication mode in the Mode dropdown list:
    • Select Detection to send touches to Workbench.
    • Select DetectionHID to send touches to the operating system. The sensor sensor module acts as a USB HID Touch Digitizer unit.

Configuring the Sensor Module

  1. In the left panel, double-click the item zForce AIR Sensor Device. Two sections, Control Panel and Device Configuration, show in the right panel.
  2. In the right panel, click the Is Enabled checkbox to enable or disable the sensor module
  3. Select communication mode in the Mode dropdown list:
    • Select Detection to send touches to Workbench.
    • Select DetectionHID to send touches to the operating system. The sensor module acts as a USB HID Touch Digitizer unit.
  4. Configure the available sensor sensor module's parameters. 
  5. Click Send Configuration to activate the selected configuration. The activated configuration is stored temporarily in the workspace. 
  6. Optional: to save the configuration for future sessions, select File >> Save Workspace.

Automatically Send the Saved Configuration to Sensor the sensor module upon Connection
Check the box Send Saved Configuration On Connect. The next time a sensor sensor module connects, Workbench sends the currently saved configuration directly to the sensormodule. This can be useful since the configuration is stored in RAM on the sensor module, which means that the sensor module will go back to default configuration after a power reset.

Restore the original configuration
Click Set Original Configuration to change the configuration of the sensor sensor module back to the configuration that the sensor module had when it first was connected to Workbench. 

Available parameters
You can configure the following sensor sensor module parameters:

ParameterDescriptionUnit
Sub Area Low Bound XStart of the Touch Active Area (TAA) in X-direction0.1 mm
Sub Area Low Bound Y

Start of the TAA in Y-direction

0.1 mm 
Sub Area High Bound XEnd of the TAA in X-direction0.1 mm
Sub Area High Bound YEnd of the TAA in Y-direction0.1 mm 
Sub Area Reverse XInverts the X axisN/A
Sub Area Reverse YInverts the Y axisN/A
Sub Area Flip XYSwaps the X and Y axis. Other sub area configurations are applied after the swap.N/A
Sub Area Offset XAdds a static offset of the TAA in X-direction0.1 mm
Sub Area Offset YAdds a static offset of the TAA in Y-direction0.1 mm
Number Of Reported TouchesHow many objects the sensor module detectsNumber of objects
Hid Display Size XDisplay size in X and Y-direction. Can for example be used when the screen size is larger than the TAA and the touches should be reported only inside the TAA (not scaled up to the entire screen). Only applicable in DetectionHid mode (HID Digitizer mode of the sensor module).0.1 mm
Hid Display Size Y
Finger FrequencyScanning frequency when one or more fingers are detectedHz
Idle FrequencyScanning frequency when no finger is activeHz

...

When the test is completed, the result appears in the right panel. Each component that was tested is represented by a box with a number inside it. The box will either be green which indicates that the test has passed, or red for fail.

Message Generator

The sensor sensor module exchanges information in messages that are structured and encoded according to the ASN.1 standard. The Message Generator tool helps you to generate ASN.1-messages in hexadecimal format. This can for example be useful when you use a microcontroller unit as host for the sensor module, and you need to send a specific message.

...